Vinny, is this a desktop computer? I have a couple older Hitachi Deskstar 7K1000.C 1TB drives I'm not using. I'll send them to you if you want. They're installed is my desktop, but I haven't touched them in quite awhile.
No warranty though!
Drive 1:
Drive 2:
No warranty though!
Drive 1:
Code:
[FONT=monospace][COLOR=#54FF54][B]stuart@office[/B][/COLOR][COLOR=#000000]:[/COLOR][COLOR=#5454FF][B]~[/B][/COLOR][COLOR=#000000]$ sudo smartctl --all /dev/sde[/COLOR]
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000
Device Model: Hitachi HDS721010KLA330
Serial Number: GTE005PBG7NUTL
LU WWN Device Id: 5 000cca 21ec37ccc
Firmware Version: GKAOAB0A
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 1
Local Time is: Sat Mar 18 10:21:17 2017 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15354) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 130 130 054 Pre-fail Offline - 151
3 Spin_Up_Time 0x0007 112 112 024 Pre-fail Always - 669 (Average 579)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 458
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 136 136 020 Pre-fail Offline - 31
9 Power_On_Hours 0x0012 091 091 000 Old_age Always - 67105
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 457
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1147
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1147
194 Temperature_Celsius 0x0002 115 115 000 Old_age Always - 52 (Min/Max 15/73)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 180
SMART Error Log Version: 1
ATA Error Count: 180 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 180 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 7f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000007f = 127
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 30 78 00 00 40 08 5d+10:12:35.100 READ FPDMA QUEUED
60 08 d8 38 00 00 40 08 5d+10:12:35.100 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 08 5d+10:12:35.100 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 5d+10:12:35.100 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 5d+10:12:35.100 IDENTIFY DEVICE
Error 179 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 3f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000003f = 63
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 c8 38 00 00 40 08 5d+10:12:34.800 READ FPDMA QUEUED
60 08 c0 18 00 00 40 08 5d+10:12:34.800 READ FPDMA QUEUED
60 08 b8 00 08 00 40 08 5d+10:12:34.800 READ FPDMA QUEUED
60 08 b0 a0 61 70 40 08 5d+10:12:34.800 READ FPDMA QUEUED
60 08 a8 f8 69 70 40 08 5d+10:12:34.800 READ FPDMA QUEUED
Error 178 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 0f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000000f = 15
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 e8 08 00 00 40 08 5d+10:12:34.400 READ FPDMA QUEUED
60 08 e0 00 00 00 40 08 5d+10:12:34.400 READ FPDMA QUEUED
60 08 d8 a0 6d 70 40 08 5d+10:12:34.400 READ FPDMA QUEUED
60 08 d0 00 6d 70 40 08 5d+10:12:34.400 READ FPDMA QUEUED
ec 00 01 00 00 00 00 08 5d+10:12:34.400 IDENTIFY DEVICE
Error 177 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 17 00 00 40 Error: ICRC, ABRT at LBA = 0x00000017 = 23
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 c8 10 00 00 40 08 5d+10:12:33.800 READ FPDMA QUEUED
60 08 c0 08 00 00 40 08 5d+10:12:33.800 READ FPDMA QUEUED
60 08 b8 00 00 00 40 08 5d+10:12:33.700 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 08 5d+10:12:33.700 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 08 5d+10:12:33.700 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 176 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 1f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000001f = 31
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 18 18 00 00 40 08 5d+10:06:36.000 READ FPDMA QUEUED
60 08 10 00 08 00 40 08 5d+10:06:36.000 READ FPDMA QUEUED
60 08 08 a0 61 70 40 08 5d+10:06:36.000 READ FPDMA QUEUED
60 08 00 f8 69 70 40 08 5d+10:06:36.000 READ FPDMA QUEUED
60 08 f0 d0 69 70 40 08 5d+10:06:36.000 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short captive Interrupted (host reset) 30% 485 -
# 2 Extended offline Aborted by host 90% 485 -
# 3 Extended captive Interrupted (host reset) 90% 485 -
# 4 Extended captive Interrupted (host reset) 90% 485 -
# 5 Extended captive Interrupted (host reset) 90% 477 -
# 6 Short offline Completed without error 00% 52916 -
# 7 Extended offline Completed without error 00% 49910 -
# 8 Extended offline Completed without error 00% 49910 -
# 9 Short offline Completed without error 00% 49899 -
#10 Extended offline Completed without error 00% 16555 -
#11 Extended offline Completed without error 00% 16387 -
#12 Extended offline Completed without error 00% 16219 -
#13 Extended offline Completed without error 00% 16051 -
#14 Extended offline Completed without error 00% 15883 -
#15 Extended offline Completed without error 00% 15715 -
#16 Extended offline Completed without error 00% 15547 -
#17 Extended offline Completed without error 00% 15380 -
#18 Extended offline Completed without error 00% 15214 -
#19 Extended offline Completed without error 00% 15044 -
#20 Extended offline Completed without error 00% 14877 -
#21 Extended offline Completed without error 00% 14707 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[/FONT]
Code:
[FONT=monospace][COLOR=#54FF54][B]stuart@office[/B][/COLOR][COLOR=#000000]:[/COLOR][COLOR=#5454FF][B]~[/B][/COLOR][COLOR=#000000]$ sudo smartctl --all /dev/sdf[/COLOR]
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.8.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000
Device Model: Hitachi HDS721010KLA330
Serial Number: GTE005PBG7S0GL
LU WWN Device Id: 5 000cca 21ec384fe
Firmware Version: GKAOAB0A
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 1
Local Time is: Sat Mar 18 10:21:59 2017 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15354) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 130 130 054 Pre-fail Offline - 150
3 Spin_Up_Time 0x0007 105 105 024 Pre-fail Always - 672 (Average 654)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 460
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 134 134 020 Pre-fail Offline - 32
9 Power_On_Hours 0x0012 091 091 000 Old_age Always - 67061
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 455
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1343
193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1343
194 Temperature_Celsius 0x0002 111 111 000 Old_age Always - 54 (Min/Max 15/69)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended captive Interrupted (host reset) 90% 440 -
# 2 Short offline Completed without error 00% 52891 -
# 3 Extended offline Completed without error 00% 49884 -
# 4 Short offline Completed without error 00% 49874 -
# 5 Extended offline Completed without error 00% 16530 -
# 6 Extended offline Completed without error 00% 16362 -
# 7 Extended offline Completed without error 00% 16194 -
# 8 Extended offline Completed without error 00% 16026 -
# 9 Extended offline Completed without error 00% 15858 -
#10 Extended offline Completed without error 00% 15690 -
#11 Extended offline Completed without error 00% 15522 -
#12 Extended offline Completed without error 00% 15355 -
#13 Extended offline Completed without error 00% 15189 -
#14 Extended offline Completed without error 00% 15018 -
#15 Extended offline Completed without error 00% 14853 -
#16 Extended offline Completed without error 00% 14682 -
#17 Extended offline Completed without error 00% 14514 -
#18 Extended offline Completed without error 00% 14346 -
#19 Extended offline Completed without error 00% 14178 -
#20 Extended offline Completed without error 00% 13885 -
#21 Extended offline Completed without error 00% 13601 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
[/FONT]
Comment