ivtv problems with pal

[easoukenka]

I purchased the pvr150 because it has pal capabilites and I knew I would be moving to europe from the usa. So I brought my nice flat screen digital tv all the way over signed up for tv and I can get a signal but it's black and white only? I have googled this issue read man files done everything I can think of... Here are a few things I have tried

v4l2-ctl switching all kinds of settings and try all the pal settings

used mythtv to switch settings scan for channels etc

used mplayer to play the video

tryed every parameter of ivtv-ctl

I still end up with black and white or no pic/ very distored pic on all pal settings. The only thing I can think of is when I run modprobe ivtv i receive the following error:
WARNING: Error inserting i2c_core (/lib/modules/2.6.24.5-smp/kernel/drivers/i2c/i2c-core.ko): Invalid module format
WARNING: Error inserting i2c_algo_bit (/lib/modules/2.6.24.5-smp/kernel/drivers/i2c/algos/i2c-algo-bit.ko): Invalid module format

however everything else seems to work and this worked on US channels fine before I came. Here is my dmesg after I remove and add seems to initialize fine even with error message.

2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
i2c_algo_bit: exports duplicate symbol i2c_bit_add_numbered_bus (owned by kernel)
ACPI: PCI interrupt for device 0000:01:08.0 disabled
ivtv0: Removed Hauppauge WinTV PVR-150, card #0
Linux video capture interface: v2.00
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
i2c_algo_bit: exports duplicate symbol i2c_bit_add_numbered_bus (owned by kernel)
ivtv: Start initialization, version 1.1.0
ivtv0: Initializing card #0
ivtv0: Autodetected Hauppauge card (cx23416 based)
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 22
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
tveeprom 2-0050: Hauppauge model 26152, rev F1B2, serial# 10389047
tveeprom 2-0050: tuner model is TCL M2523_5N_E (idx 112, type 50)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has no radio, has IR receiver, has IR transmitter
ivtv0: Autodetected Hauppauge WinTV PVR-150
ivtv0: Reopen i2c bus for IR-blaster support
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 2-0044: cx25843-24 found @ 0x88 (ivtv i2c driver #0)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
i2c_core: exports duplicate symbol i2c_smbus_xfer (owned by kernel)
tuner-simple 2-0061: type set to 50 (TCL 2002N)
tuner 2-0061: type set to TCL 2002N
ivtv0: Registered device video0 for encoder MPG (4096 kB)
ivtv0: Registered device video32 for encoder YUV (2048 kB)
ivtv0: Registered device vbi0 for encoder VBI (1024 kB)
ivtv0: Registered device video24 for encoder PCM (320 kB)
ivtv0: Initialized card #0: Hauppauge WinTV PVR-150
ivtv: End initialization


Any help would be very appreciated thank you for your time.

I did want to add that I am just trying to get output right now on a computer monitor i purchased in europe the tv will be for later.

[dibl]

Re: ivtv problems with pal

This is a little dated, and written for USA implementation, but maybe you'll see something helpful:

http://kubuntuforums.net/forums/inde...opic=3085164.0

[easoukenka]

Re: ivtv problems with pal

ok I just reinstalled my operating system i do not get any errors anymore but the display is still in black and white? I will continue to try to fix this and post any information I find thank you.